MPPT 60A/40A/30A/20A Solar Charge Controller 12V 24V 36V 48V Battery Regulator

Description

FEATURE
Charging 3-stage: constant current(MPPT), constant voltage(Absorption Voltage), floating charge
Selectable battery type Vented / Sealed / Gel / NiCd / Lithium battery (default is Sealed) (defined voltage for other battery by user)
Soft start time ≤1S, Dynamic response and recovery time 100us
Max efficiency ≥98.1%, PV utilization ≥99%
In order to reduce the cost of electricity caused by high current, PV and battery each have two terminals
MULTIPLE ELECTRONIC PROTECTIONS
Short-circuting
Reverse-current
Overcharging
Overload
Over-discharging
Reverse polarity protection
Maximum PV Input Power
Ensure that the solar input voltage exceeds 3v or is higher than the battery voltage.
12 Volt Battery Systems: Maximum PV input power 720 watts, recommended solar input voltage range 20 - 80 volts DC.
24 Volt Battery Systems: Maximum PV input power 1440 watts, recommended PV input voltage range 37 - 105 VDC
36 volt battery system: 2100 watt maximum PV input, recommended PV input voltage range 50 - 150 volts DC
48 volt battery system: 2800 watt maximum PV input, recommended PV input voltage range 72 - 150 volts DC
Installation Procedure
Installation Procedure
Install the switch between the controller and the battery.
Install a switch between the controller and the PV module.
Check that the "+" and "-" of the PV module and the "+" and "-" of the battery are correctly connected.
Turn on the battery switch first, then turn on the PV switch.
LCD display
ESC: Exit the setting without saving the data.
UP: Scroll down, adjust the parameter by increasing the value.
DOWN: Scroll up, adjust the parameter by decreasing the value.
ENTER: Short press to move to the next setting page, long press to exit the setting and save the data.
Display Code Meaning
Display Code Meaning
EQU: Load voltage compensation
BST: Pulse charging voltage
FLD: Load voltage hold
LDV: Over-discharge voltage
LRV: Over-discharge recovery voltage
BST - r: Pulse charge recovery voltage
Battery type: FLD/SEL/Gel/Lithium/Use
Warning and Caution
1. the battery voltage must be higher than 12v for the controller to start.
2. make sure that the solar input voltage exceeds 3v or the battery voltage. 3. hold the wiring correctly and do not change the wiring.
3. hold the wiring correctly and do not change the wiring. pay attention to the order of the terminal wiring.
4. if it is a lead acid battery, if it is not professional, do not set any parameter, because in addition to the lithium battery, the controller also works well in the standard state.
5. do not connect solar inverters / generators / wind turbines to the controller.
6. Install the controller indoors to prevent the components from entering the water.
7.Maximum PV input voltage (voc): 180 V dc, the controller cannot work for a long time under this voltage, which will damage the controller.
8. Disconnect the battery and reconnect to save the configuration.
40A 30A 20A MPPT solar charge controller(Fan cooling)
12V/24V(auto detection);32V(setting)
MPPT efficiency>99%,Peak conversion
efficiency >98%
DSP processors technology ensure high
speed and performance
Multi-stage charging mode
Protection: PV array short circuit ,
PV reverse polarity , Battery reverse polarity ,
Over charging , Output short circuit
Equalization charging function
BTS function
Models
ICharer MPPT 2420 2430 2440
Rated charge current
20A/30A/40A
System Voltage
12/24V Auto recognized
Max PV Input Power
260W(12V) 260W(12V)/ 260W(12V) 260W(12V)/520W(12V)
1040W (24V)
Solar panel inputrange
16.8V-60V(12V) 33.6V-
60V
(24V) /16.8V-60V(12V) 33.6V-60V(24V)/16.8V-60V(12V)33.6V-60V(24V)
BatteryVoltageAutom
aticRecognition
12VSystem(DC8.7V-DC15.SV)24VSystem(DC16V-DC31V)
36VSystem(DC33V-DC41V)48VSystem(DC42V-DC64V)
Maximum batteryvoltage
8V-32V
Battery type
Battery type
LVD
Maintenance-free lead-acid battery, GEL, lead-acid Flooded battery :10.8V
LVR
Maintenance-free lead-acid battery, GEL, lead-acid Flooded battery :12.6V
HVD
Lead acid battery 16V
Temperature compensationcoefficient
-4mV/°C/2V(25°C)
Fan-onTemperature
>45
℃
Fan-offTemperature
<40
℃
Size(mm)
247.3*201*80.3
NeWteight(Kg)
1.5
Light control voltage
≤90%, No condensation
Enclosure
IP30
Opertation Temperature
-20°C~
＋
55°C
Storage Temperature
-30°C~
＋
70°C